Which two of these parameters are used to determine a forwarding equivalence class? (Choose two.)
A. IP prefix
B. Layer 2 circuit
C. RSVP request from CE for bandwidth reservation
D. BGP MED value
A network is composed of several VRFs. It is required that VRF users VRF_A and VRF_B be able to route to and from VRF_C, which hosts shared services. However, traffic must not be allowed to flow between VRF_A and VRF_B. How can this be accomplished?
A. route redistribution
B. import and export using route descriptors
C. import and export using route targets
D. Cisco MPLS Traffic Engineering
Which of these statements best describes the major difference between an IPv4-compatible tunnel and a 6to4 tunnel?
A. An IPv4-compatible tunnel is a static tunnel, but an 6to4 tunnel is a semiautomatic tunnel.
B. The deployment of a IPv4-compatible tunnel requires a special code on the edge routers, but a 6to4 tunnel does not require any special code.
C. An IPv4-compatible tunnel is typically used only between two IPv6 domains, but a 6to4 tunnel is used to connect to connect two or more IPv6 domains.
D. For an IPv4-compatible tunnel, the ISP assigns only IPv4 addresses for each domain, but for a 6to4 tunnel, the ISP assigns only IPv6 addresses for each domain.
Which information is carried in an OSPFv3 intra-area-prefix LSA?
A. IPv6 prefixes
B. link-local addresses
C. solicited node multicast addresses
D. IPv6 prefixes and topology information
Which IPv6 address would you ping to determine if OSPFv3 is able to send and receive unicast packets across a link?
A. anycast address
B. site-local multicast
C. global address of the link
D. unique local address
E. link-local address
You are using IPv6, and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration? (Choose three.)
A. EIGRP for IPv6 is directly configured on the interfaces over which it runs.
B. EIGRP for IPv6 is not configured on the interfaces over which it runs, but if a user uses passive-interface configuration, EIGRP for IPv6 needs to be configured on the interface that is made passive.
C. There is a network statement configuration in EIGRP for IPv6, the same as for IPv4.
D. There is no network statement configuration in EIGRP for IPv6.
E. When a user uses a passive-interface configuration, EIGRP for IPv6 does not need to be configured on the interface that is made passive.
F. When a user uses a non-passive-interface configuration, EIGRP for IPv6 does not need to be configured on the interface that is made passive
Which of these statements accurately identifies how Unicast Reverse Path Forwarding can be employed to prevent the use of malformed or forged IP sources addresses?
A. It is applied only on the input interface of a router.
B. It is applied only on the output interface of a router.
C. It can be configured either on the input or output interface of a router.
D. It cannot be configured on a router interface.
E. It is configured under any routing protocol process.
Unicast Reverse Path Forwarding can perform all of these actions except which one?
A. examine all packets received to make sure that the source addresses and source interfaces appear in the routing table and match the interfaces where the packets were received
B. check to see if any packet received at a router interface arrives on the best return path
C. combine with a configured ACL
D. log its events, if you specify the logging options for the ACL entries used by the unicast rpf command
E. inspect IP packets encapsulated in tunnels, such as GRE
Which three of these statements about Dynamic Trunking Protocol are correct? (Choose three.)
A. It supports autonegotiation for both ISL and IEEE 802.1Q trunks.
B. It must be disabled on an interface if you do not want the interface to work as a trunk or start negotiation to become a trunk.
C. It is a point-to-multipoint protocol.
D. It is a point-to-point protocol.
E. It is not supported on private VLAN ports or tunneling ports.
You are designing your network to be able to use trunks. As part of this process you are comparing the ISL and 802.1Q encapsulation options. All of these statements about the two encapsulation options are correct except which one?
A. Both support normal and extended VLAN ranges.
B. ISL is a Cisco proprietary encapsulation method and 802.1Q is an IEEE standard.
C. ISL encapsulates the original frame.
D. Both support native VLANs.
E. 802.1Q does not encapsulate the original frame.
Passleader 350-001 Braindumps Help You Pass Exam With 100% Money Back