web analytics

PassLeader 100% Pass Guaranteed IT Exam Dumps Free Download

Free Collection of VCE and PDF Braindump with New Exam Questions

The Professional Cisco 350-001 Exam Free Dumps Help You 100% Pass Exam (11-20)

QUESTION 11
How is RPF used in multicast routing?

A.    to prevent multicast packets from looping
B.    to prevent PIM packets from looping
C.    to instruct PIM where to send a (*,G) or (S,G) join message
D.    to prevent multicast packets from looping and to instruct PIM where to send a (*,G) or (S,G) join message

Answer: D

QUESTION 12
Refer to the exhibit. What does the incoming interface of the above (*,G) entry indicate?
121
A.    the interface closest to the source, according to the unicast routing table
B.    the interface where an IGMP join has been received
C.    the interface with the highest IP address
D.    the last interface to hear a PIM (*,G) join
E.    the interface closest to the RP, according to the unicast routing table

Answer: E

QUESTION 13
Refer to the exhibit. Which interface(s) will show ip rpf 1.1.1.2 indicate as RPF interface(s)?
131

A.    Ethernet 1/0
B.    Ethernet 0/0
C.    Both Ethernet 0/0 and Ethernet 1/0
D.    RPF will fail

Answer: A

QUESTION 14
Apart from interdomain multicast routing, what else is MSDP used for?

A.    Source Specific Multicast and IGMPv2
B.    Announcing multicast sources to BGP speakers
C.    Anycast RP
D.    Intradomain multicast routing

Answer: C

QUESTION 15
Which IGMPv2 message contains a non-zero “Max Response Time”?

A.    Membership Query
B.    Membership Report
C.    Membership Delay
D.    Backward Compatible IGMPv1 Report Message

Answer: A

QUESTION 16
Refer to the exhibit. Which IGMPv2 message is displayed in the output of the packet capture?
161
A.    General Query
B.    Membership Report
C.    Membership Query
D.    Membership Delay

Answer: B

QUESTION 17
What is Phantom RP used for?

A.    it is used for load balancing in bidirectional PIM
B.    it is used for redundancy in bidirectional PIM
C.    it is used for redundancy in PIM-SM
D.    it is used for load balancing in PIM-SM

Answer: B

QUESTION 18
Which three statements are true about TACACS+? (Choose three.)

A.    It is a Cisco proprietary protocol.
B.    It runs on TCP port 59.
C.    Authentication and authorization are done at different stages.
D.    TACACS+ encrypts the entire body of the packet, but leaves a standard TACACS+ header.
E.    It is an industry standard protocol.
F.    TACACS+ encrypts both the entire body of the packet and the TACACS+ header.

Answer: ACD

QUESTION 19
Refer to the exhibit. Which two statements are correct? (Choose two.)
191

A.    The hexadecimal value of the number of packets that hit the access list is 0x723E6E12.
B.    The access list has logging enabled.
C.    The packet was discarded.
D.    The command ip access-list logging hash-generation is enabled.
E.    The Telnet connection is successfully set up.

Answer: BD

QUESTION 20
Refer to the exhibit. Which statement is correct?
 
A.    This configuration is not valid.
B.    Control Plane Policing is configured; however you cannot determine on which interface it is configured.
C.    NTP is not configured on the router.
D.    Telnet traffic will be dropped.

Answer: C

The Professional Cisco 350-001 Exam Free Dumps Help You 100% Pass Exam

         

Latest and 100% Pass Guaranteed IT Exam Dumps Download © 2015 Frontier Theme